1818 lines
49 KiB
C
1818 lines
49 KiB
C
/*
|
|
* mops.c
|
|
*
|
|
* This file is part of Emu48
|
|
*
|
|
* Copyright (C) 1995 Sebastien Carlier
|
|
*
|
|
*/
|
|
#include "pch.h"
|
|
#include "Emu48.h"
|
|
#include "ops.h"
|
|
#include "opcodes.h"
|
|
#include "io.h"
|
|
#include "i28f160.h" // flash support
|
|
|
|
// #define DEBUG_SERIAL // switch for SERIAL debug purpose
|
|
// #define DEBUG_IO // switch for I/O debug purpose
|
|
// #define DEBUG_FLASH // switch for FLASH MEMORY debug purpose
|
|
|
|
// defines for reading an open data bus
|
|
#define READEVEN 0x0D
|
|
#define READODD 0x0E
|
|
|
|
// on mapping boundary adjusted base addresses
|
|
#define P0MAPBASE ((BYTE)(Chipset.P0Base & ~Chipset.P0Size))
|
|
#define P1MAPBASE ((BYTE)(Chipset.P1Base & ~Chipset.P1Size))
|
|
#define P2MAPBASE ((BYTE)(Chipset.P2Base & ~Chipset.P2Size))
|
|
#define BSMAPBASE ((BYTE)(Chipset.BSBase & ~Chipset.BSSize))
|
|
|
|
BOOL bFlashRomArray = TRUE; // flag ROM mode
|
|
|
|
BYTE disp = 0; // flag for update display area
|
|
|
|
static LPBYTE pbyRomView[2] = {NULL, NULL}; // HP49G ROM views
|
|
|
|
// CRC calculation
|
|
static WORD crc_table[] =
|
|
{
|
|
0x0000, 0x1081, 0x2102, 0x3183, 0x4204, 0x5285, 0x6306, 0x7387,
|
|
0x8408, 0x9489, 0xA50A, 0xB58B, 0xC60C, 0xD68D, 0xE70E, 0xF78F
|
|
};
|
|
static __inline VOID UpCRC(BYTE nib)
|
|
{
|
|
Chipset.crc = (WORD)((Chipset.crc>>4)^crc_table[(Chipset.crc^nib)&0xf]);
|
|
}
|
|
|
|
static __inline UINT MIN(UINT a, UINT b)
|
|
{
|
|
return (a<b)?a:b;
|
|
}
|
|
|
|
static __inline UINT MAX(UINT a, UINT b)
|
|
{
|
|
return (a>b)?a:b;
|
|
}
|
|
|
|
// generate UCK signal
|
|
static __inline BYTE UckBit(BYTE byBaudIndex)
|
|
{
|
|
// table content = baudrate * 16
|
|
const DWORD dwBaudrates[] = { 19200, 30720, 38400, 61440, 76800, 122880, 153600, 245760 };
|
|
|
|
LARGE_INTEGER lLC;
|
|
|
|
_ASSERT(byBaudIndex < ARRAYSIZEOF(dwBaudrates));
|
|
|
|
if ((Chipset.IORam[IOC] & SON) == 0) // UART off
|
|
return UCK; // UCK bit always set
|
|
|
|
QueryPerformanceCounter(&lLC); // get counter value
|
|
|
|
// calculate UCK frequency
|
|
return (((BYTE)(((lLC.QuadPart - lAppStart.QuadPart) * dwBaudrates[byBaudIndex])
|
|
/ lFreq.QuadPart) & 0x1) << 3);
|
|
}
|
|
|
|
// calculate nibble based linear flash address
|
|
static __inline DWORD FlashROMAddr(DWORD d)
|
|
{
|
|
DWORD dwLinAddr;
|
|
|
|
// 6 bit of latch (was A6-A1 of address bus)
|
|
dwLinAddr = (Chipset.Bank_FF >> 1) & 0x3f;
|
|
// decode A21-A18
|
|
dwLinAddr = ((d & 0x40000) ? (dwLinAddr & 0xf) : (dwLinAddr >> 4)) << 18;
|
|
// decode A21-A18, A17-A0
|
|
dwLinAddr |= d & 0x3FFFF;
|
|
return dwLinAddr;
|
|
}
|
|
|
|
// update display
|
|
static __inline VOID UpdateDisplay(DWORD d, UINT s)
|
|
{
|
|
BYTE p[16];
|
|
DWORD u;
|
|
UINT c;
|
|
|
|
// address in display main area?
|
|
if ((d<Chipset.end1)&&(d+s>Chipset.start12))
|
|
{
|
|
// write to display main area
|
|
u = d; // copy destination ptr
|
|
c = MIN(s,Chipset.end1-d); // number of nibbles to copy
|
|
|
|
if (d < Chipset.start12) // first address is out of display area
|
|
{
|
|
u = Chipset.start12; // set destination ptr to start of display area
|
|
c -= Chipset.start12 - d; // - number of bytes that aren't in display area
|
|
}
|
|
|
|
_ASSERT(c <= ARRAYSIZEOF(p));
|
|
Npeek(p,u,c); // get source data
|
|
WriteToMainDisplay(p,u,c);
|
|
}
|
|
// address in display menu area?
|
|
if ((d<Chipset.end2)&&(d+s>Chipset.start2))
|
|
{
|
|
// write to display menu area
|
|
u = d; // copy destination ptr
|
|
c = MIN(s,Chipset.end2-d); // number of nibbles to copy
|
|
|
|
if (d < Chipset.start2) // first address is out of display area
|
|
{
|
|
u = Chipset.start2; // set destination ptr to start of display area
|
|
c -= Chipset.start2 - d; // - number of bytes that are not in display area
|
|
}
|
|
|
|
_ASSERT(c <= ARRAYSIZEOF(p));
|
|
Npeek(p,u,c); // get source data
|
|
WriteToMenuDisplay(p,u,c);
|
|
}
|
|
return;
|
|
}
|
|
|
|
// port mapping
|
|
|
|
LPBYTE RMap[256] = {NULL,};
|
|
LPBYTE WMap[256] = {NULL,};
|
|
|
|
static VOID MapP0(BYTE a, BYTE b)
|
|
{
|
|
UINT i;
|
|
DWORD p, m;
|
|
|
|
a = (BYTE)MAX(a,P0MAPBASE); // adjust base to mapping boundary
|
|
b = (BYTE)MIN(b,Chipset.P0End);
|
|
m = (Chipset.Port0Size*2048)-1;
|
|
p = (a<<12)&m; // offset to begin of P0 in nibbles
|
|
for (i=a; i<=b; i++)
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P0Base) & ~Chipset.P0Size) == 0)
|
|
{
|
|
RMap[i]=Port0 + p;
|
|
WMap[i]=Port0 + p;
|
|
}
|
|
p = (p+0x1000)&m;
|
|
}
|
|
return;
|
|
}
|
|
|
|
static VOID MapBS(BYTE a, BYTE b)
|
|
{
|
|
UINT i;
|
|
|
|
a = (BYTE)MAX(a,BSMAPBASE); // adjust base to mapping boundary
|
|
b = (BYTE)MIN(b,Chipset.BSEnd);
|
|
for (i=a;i<=b;i++)
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.BSBase) & ~Chipset.BSSize) == 0)
|
|
{
|
|
RMap[i]=NULL; // no read cycle, open data bus
|
|
WMap[i]=NULL;
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
static VOID MapP1(BYTE a, BYTE b)
|
|
{
|
|
UINT i;
|
|
DWORD p, m;
|
|
|
|
// clear mapping area if port1 is configured but not plugged
|
|
a = (BYTE)MAX(a,P1MAPBASE); // lowest address for use is P1Base
|
|
b = (BYTE)MIN(b,Chipset.P1End); // highest address for use is P1End
|
|
|
|
// port1 not plugged
|
|
if (Port1 == NULL || !(Chipset.cards_status & PORT1_PRESENT))
|
|
{
|
|
for (i=a; i<=b; i++) // scan each 2KB page
|
|
{
|
|
if (((i ^ Chipset.P1Base) & ~Chipset.P1Size) == 0)
|
|
{
|
|
RMap[i]=NULL;
|
|
WMap[i]=NULL;
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
m = (Chipset.Port1Size*2048)-1; // real size of module, address mask for mirroring
|
|
p = (a<<12)&m; // offset to begin of P1 in nibbles
|
|
|
|
if (Chipset.cards_status & PORT1_WRITE) // port1 write enabled
|
|
{
|
|
for (i=a; i<=b; i++) // scan each 2KB page
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P1Base) & ~Chipset.P1Size) == 0)
|
|
{
|
|
RMap[i]=Port1 + p; // save page address for read
|
|
WMap[i]=Port1 + p; // save page address for write
|
|
}
|
|
p = (p+0x1000)&m; // next page, mirror page if real size smaller allocated size
|
|
}
|
|
}
|
|
else // port1 read only
|
|
{
|
|
for (i=a; i<=b; i++) // scan each 2KB page
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P1Base) & ~Chipset.P1Size) == 0)
|
|
{
|
|
RMap[i]=Port1 + p; // save page address for read
|
|
WMap[i]=NULL; // no writing
|
|
}
|
|
p = (p+0x1000)&m; // next page, mirror page if real size smaller allocated size
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
static VOID MapP2(BYTE a, BYTE b)
|
|
{
|
|
UINT i;
|
|
DWORD p, m;
|
|
LPBYTE pbyTemp;
|
|
|
|
// clear mapping area if port2 is configured but not plugged
|
|
a = (BYTE)MAX(a,P2MAPBASE); // adjust base to mapping boundary
|
|
b = (BYTE)MIN(b,Chipset.P2End);
|
|
|
|
if (Chipset.Port2Size) // internal port2
|
|
{
|
|
m = (Chipset.Port2Size*2048)-1;
|
|
p = (a<<12)&m; // offset to begin of P0 in nibbles
|
|
for (i=a; i<=b; i++)
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P2Base) & ~Chipset.P2Size) == 0)
|
|
{
|
|
RMap[i]=Port2 + p;
|
|
WMap[i]=Port2 + p;
|
|
}
|
|
p = (p+0x1000)&m;
|
|
}
|
|
return;
|
|
}
|
|
|
|
// HP48SX / HP48GX
|
|
// only fill mapping table when CE2.2 is set
|
|
for (i=a; i<=b; i++) // fill mapping area with not configured
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P2Base) & ~Chipset.P2Size) == 0)
|
|
{
|
|
RMap[i]=NULL;
|
|
WMap[i]=NULL;
|
|
}
|
|
}
|
|
|
|
// port2 not plugged
|
|
if (pbyPort2 == NULL || !(Chipset.cards_status & PORT2_PRESENT))
|
|
return;
|
|
|
|
pbyTemp = pbyPort2;
|
|
if (cCurrentRomType != 'S') // bank switching only with GX
|
|
{
|
|
// Chipset.Port2_Bank is the saved port2 FF content
|
|
pbyTemp += (((Chipset.Bank_FF>>1)-1)&dwPort2Mask) << 18;
|
|
}
|
|
|
|
// max. size per bank is 128KB
|
|
m = (dwPort2Size > 128) ? 128 : dwPort2Size;
|
|
|
|
m = (m * 2048) - 1; // real size of module, address mask for mirroring
|
|
p = (a << 12) & m; // offset to begin of P2 in nibbles
|
|
|
|
// SX: CE2.2 = CE2
|
|
// GX: CE2.2 = BEN & /DA19 & /NCE3
|
|
if (cCurrentRomType == 'S' || ((Chipset.IORam[0x29]&DA19) == 0 && (Chipset.Bank_FF&0x40)))
|
|
{
|
|
if (bPort2Writeable)
|
|
{
|
|
for (i=a; i<=b; i++)
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P2Base) & ~Chipset.P2Size) == 0)
|
|
{
|
|
RMap[i]=pbyTemp + p;
|
|
WMap[i]=pbyTemp + p;
|
|
}
|
|
p = (p+0x1000)&m;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
for (i=a; i<=b; i++)
|
|
{
|
|
// mapping area may have holes
|
|
if (((i ^ Chipset.P2Base) & ~Chipset.P2Size) == 0)
|
|
{
|
|
RMap[i]=pbyTemp + p;
|
|
}
|
|
p = (p+0x1000)&m;
|
|
}
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
static VOID MapROM(BYTE a, BYTE b)
|
|
{
|
|
UINT i;
|
|
DWORD p, m;
|
|
|
|
// HP39/49G, HP49G
|
|
if (cCurrentRomType == 'E' || cCurrentRomType == 'X')
|
|
{
|
|
if (bFlashRomArray) // view flash ROM data
|
|
{
|
|
_ASSERT(pbyRomView[0]); // check ROM bank set
|
|
_ASSERT(pbyRomView[1]);
|
|
|
|
m = (128*1024*2)-1; // mapped in 128KB pages
|
|
p = (a<<12)&m; // offset to the begin of ROM in nibbles
|
|
for (i=a; i<=b; i++) // scan each 2KB page
|
|
{
|
|
RMap[i]=pbyRomView[(i & 0x40)!=0] + p;
|
|
WMap[i]=NULL; // no writing
|
|
p = (p+0x1000)&m;
|
|
}
|
|
}
|
|
else // view flash ROM register
|
|
{
|
|
for (i=a; i<=b; i++) // scan each 2KB page
|
|
{
|
|
RMap[i]=NULL; // view flash register
|
|
WMap[i]=NULL; // no writing
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
// HP38G / HP48SX / HP48GX
|
|
m = dwRomSize - 1; // ROM address mask for mirroring
|
|
// when 512KB ROM and DA19=0 (ROM disabled)
|
|
if ((m & 0x80000) != 0 && (Chipset.IORam[0x29]&DA19) == 0)
|
|
m >>= 1; // mirror ROM at #80000 (AR18=0)
|
|
p = (a*0x1000)&m; // data offset in nibbles
|
|
for (i=a;i<=b;i++) // scan each 2KB page
|
|
{
|
|
RMap[i]=pbyRom + p; // save page address for read
|
|
WMap[i]=NULL; // no writing
|
|
p = (p+0x1000)&m; // next page, mirror page if real size smaller allocated size
|
|
}
|
|
return;
|
|
}
|
|
|
|
VOID Map(BYTE a, BYTE b) // maps 2KB pages with priority
|
|
{
|
|
// On HP39/40G and HP49G Chipset.cards_status must be 0xF
|
|
_ASSERT((cCurrentRomType!='E' && cCurrentRomType!='X') || !Chipset.P1Cfig || Chipset.cards_status == 0xF);
|
|
|
|
// priority order is HDW, RAM, CE2, CE1, NCE3, ROM
|
|
MapROM(a,b); // ROM, lowest priority, always mapped
|
|
if (cCurrentRomType == 'S') // HP48SX
|
|
{
|
|
if (Chipset.BSCfig) MapBS(a,b); // NCE3, not used in S(X)
|
|
if (Chipset.P1Cfig) MapP1(a,b); // CE1, port1 (lower priority than CE2)
|
|
if (Chipset.P2Cfig) MapP2(a,b); // CE2, port2 (higher priority than CE1)
|
|
}
|
|
else // HP48GX / HP49G
|
|
{
|
|
if (Chipset.P2Cfig) // NCE3, port2
|
|
{
|
|
// LED bit set on a HP49
|
|
if (cCurrentRomType=='X' && (Chipset.IORam[LCR]&LED))
|
|
MapROM(a,b); // NCE3, ROM
|
|
else
|
|
MapP2(a,b); // NCE3, port2
|
|
}
|
|
if (Chipset.BSCfig) MapBS(a,b); // CE1, bank select (lower priority than CE2)
|
|
if (Chipset.P1Cfig) MapP1(a,b); // CE2, port1 (higher priority than CE1)
|
|
}
|
|
if (Chipset.P0Cfig) MapP0(a,b); // RAM, highest priority (execpt HDW)
|
|
return;
|
|
}
|
|
|
|
VOID RomSwitch(DWORD adr)
|
|
{
|
|
// only HP39/40G, HP49G
|
|
if (cCurrentRomType=='E' || cCurrentRomType=='X')
|
|
{
|
|
Chipset.Bank_FF = adr; // save address line
|
|
adr = (adr >> 1) & 0x3f; // 6 bit of latch (was A6-A1 of address bus)
|
|
// lower 4 bit (16 banks) for 2nd ROM view
|
|
pbyRomView[1] = pbyRom + (((adr & 0xf) * 128 * 1024 * 2) & (dwRomSize - 1));
|
|
// higher 2 bit (4 banks) for 1st ROM view
|
|
pbyRomView[0] = pbyRom + (((adr >> 4) * 128 * 1024 * 2) & (dwRomSize - 1));
|
|
}
|
|
Map(0x00,0xFF); // update memory mapping
|
|
return;
|
|
}
|
|
|
|
////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Bus Commands
|
|
//
|
|
////////////////////////////////////////////////////////////////////////////////
|
|
|
|
VOID Config() // configure modules in fixed order
|
|
{
|
|
DWORD d = Npack(Chipset.C,5); // decode size or address
|
|
BYTE b = (BYTE)(d>>12); // number of 2KB pages or page address
|
|
BYTE s = (BYTE)(b^0xFF); // size in pages-1, offset to last page
|
|
|
|
// config order is HDW, RAM, CE1, CE2, NCE3
|
|
if (!Chipset.IOCfig) // address of HDW, first module, ROM always configured
|
|
{
|
|
Chipset.IOCfig = TRUE;
|
|
Chipset.IOBase = d&0xFFFC0; // save HDW base on a 64 nib boundary
|
|
Map(b,b);
|
|
return;
|
|
}
|
|
if (!Chipset.P0Cfg2) // RAM size, port0
|
|
{
|
|
Chipset.P0Cfg2 = TRUE;
|
|
Chipset.P0Size = s; // offset to last used page
|
|
return;
|
|
}
|
|
if (!Chipset.P0Cfig) // RAM address, port0
|
|
{
|
|
Chipset.P0Cfig = TRUE;
|
|
Chipset.P0Base = b; // save first page address
|
|
b &= ~Chipset.P0Size; // adjust base to mapping boundary
|
|
Chipset.P0End = b+Chipset.P0Size; // save last page address
|
|
Map(b,Chipset.P0End); // refresh mapping
|
|
return;
|
|
}
|
|
if (cCurrentRomType=='S') // HP48SX
|
|
{
|
|
if (!Chipset.P1Cfg2) // CE1 size, port1
|
|
{
|
|
Chipset.P1Cfg2 = TRUE;
|
|
Chipset.P1Size = s;
|
|
return;
|
|
}
|
|
if (!Chipset.P1Cfig) // CE1 address, port1
|
|
{
|
|
Chipset.P1Cfig = TRUE;
|
|
Chipset.P1Base = b;
|
|
b &= ~Chipset.P1Size; // adjust base to mapping boundary
|
|
Chipset.P1End = b+Chipset.P1Size;
|
|
Map(b,Chipset.P1End); // refresh mapping
|
|
return;
|
|
}
|
|
if (!Chipset.P2Cfg2) // CE2 size, port2
|
|
{
|
|
Chipset.P2Cfg2 = TRUE;
|
|
Chipset.P2Size = s;
|
|
return;
|
|
}
|
|
if (!Chipset.P2Cfig) // CE2 address, port2
|
|
{
|
|
Chipset.P2Cfig = TRUE;
|
|
Chipset.P2Base = b;
|
|
b &= ~Chipset.P2Size; // adjust base to mapping boundary
|
|
Chipset.P2End = b+Chipset.P2Size;
|
|
Map(b,Chipset.P2End); // refresh mapping
|
|
return;
|
|
}
|
|
if (!Chipset.BSCfg2) // NCE3 size, not used in S(X)
|
|
{
|
|
Chipset.BSCfg2 = TRUE;
|
|
Chipset.BSSize = s;
|
|
return;
|
|
}
|
|
if (!Chipset.BSCfig) // NCE3 address, not used in S(X)
|
|
{
|
|
Chipset.BSCfig = TRUE;
|
|
Chipset.BSBase = b;
|
|
b &= ~Chipset.BSSize; // adjust base to mapping boundary
|
|
Chipset.BSEnd = b+Chipset.BSSize;
|
|
Map(b,Chipset.BSEnd); // refresh mapping
|
|
return;
|
|
}
|
|
}
|
|
else // HP48GX / HP49G
|
|
{
|
|
if (!Chipset.BSCfg2) // CE1 size, bank select
|
|
{
|
|
Chipset.BSCfg2 = TRUE;
|
|
Chipset.BSSize = s;
|
|
return;
|
|
}
|
|
if (!Chipset.BSCfig) // CE1 address, bank select
|
|
{
|
|
Chipset.BSCfig = TRUE;
|
|
Chipset.BSBase = b;
|
|
b &= ~Chipset.BSSize; // adjust base to mapping boundary
|
|
Chipset.BSEnd = b+Chipset.BSSize;
|
|
Map(b,Chipset.BSEnd); // refresh mapping
|
|
return;
|
|
}
|
|
if (!Chipset.P1Cfg2) // CE2 size, port1
|
|
{
|
|
Chipset.P1Cfg2 = TRUE;
|
|
Chipset.P1Size = s;
|
|
return;
|
|
}
|
|
if (!Chipset.P1Cfig) // CE2 address, port1
|
|
{
|
|
Chipset.P1Cfig = TRUE;
|
|
Chipset.P1Base = b;
|
|
b &= ~Chipset.P1Size; // adjust base to mapping boundary
|
|
Chipset.P1End = b+Chipset.P1Size;
|
|
Map(b,Chipset.P1End); // refresh mapping
|
|
return;
|
|
}
|
|
if (!Chipset.P2Cfg2) // NCE3 size, port2
|
|
{
|
|
Chipset.P2Cfg2 = TRUE;
|
|
Chipset.P2Size = s;
|
|
return;
|
|
}
|
|
if (!Chipset.P2Cfig) // NCE3 address, port2
|
|
{
|
|
Chipset.P2Cfig = TRUE;
|
|
Chipset.P2Base = b;
|
|
b &= ~Chipset.P2Size; // adjust base to mapping boundary
|
|
Chipset.P2End = b+Chipset.P2Size;
|
|
Map(b,Chipset.P2End); // refresh mapping
|
|
return;
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
VOID Uncnfg()
|
|
{
|
|
DWORD d=Npack(Chipset.C,5); // decode address
|
|
BYTE b=(BYTE)(d>>12); // page address
|
|
|
|
// unconfig order is HDW, RAM, CE2, CE1, NCE3
|
|
if ((Chipset.IOCfig)&&((d&0xFFFC0)==Chipset.IOBase))
|
|
{Chipset.IOCfig=FALSE;Map(b,b);return;}
|
|
if ((Chipset.P0Cfig)&&((b&~Chipset.P0Size)==P0MAPBASE))
|
|
{Chipset.P0Cfig=FALSE;Chipset.P0Cfg2=FALSE;Map(P0MAPBASE,Chipset.P0End);return;}
|
|
if (cCurrentRomType=='S') // HP48SX
|
|
{
|
|
if ((Chipset.P2Cfig)&&((b&~Chipset.P2Size)==P2MAPBASE))
|
|
{Chipset.P2Cfig=FALSE;Chipset.P2Cfg2=FALSE;Map(P2MAPBASE,Chipset.P2End);return;}
|
|
if ((Chipset.P1Cfig)&&((b&~Chipset.P1Size)==P1MAPBASE))
|
|
{Chipset.P1Cfig=FALSE;Chipset.P1Cfg2=FALSE;Map(P1MAPBASE,Chipset.P1End);return;}
|
|
if ((Chipset.BSCfig)&&((b&~Chipset.BSSize)==BSMAPBASE))
|
|
{Chipset.BSCfig=FALSE;Chipset.BSCfg2=FALSE;Map(BSMAPBASE,Chipset.BSEnd);return;}
|
|
}
|
|
else // HP48GX / HP49G
|
|
{
|
|
if ((Chipset.P1Cfig)&&((b&~Chipset.P1Size)==P1MAPBASE))
|
|
{Chipset.P1Cfig=FALSE;Chipset.P1Cfg2=FALSE;Map(P1MAPBASE,Chipset.P1End);return;}
|
|
if ((Chipset.BSCfig)&&((b&~Chipset.BSSize)==BSMAPBASE))
|
|
{Chipset.BSCfig=FALSE;Chipset.BSCfg2=FALSE;Map(BSMAPBASE,Chipset.BSEnd);return;}
|
|
if ((Chipset.P2Cfig)&&((b&~Chipset.P2Size)==P2MAPBASE))
|
|
{Chipset.P2Cfig=FALSE;Chipset.P2Cfg2=FALSE;Map(P2MAPBASE,Chipset.P2End);return;}
|
|
}
|
|
return;
|
|
}
|
|
|
|
VOID Reset()
|
|
{
|
|
Chipset.IOCfig=FALSE;Chipset.IOBase=0x100000;
|
|
Chipset.P0Cfig=FALSE;Chipset.P0Cfg2=FALSE;Chipset.P0Base=0;Chipset.P0Size=0;Chipset.P0End=0;
|
|
Chipset.BSCfig=FALSE;Chipset.BSCfg2=FALSE;Chipset.BSBase=0;Chipset.BSSize=0;Chipset.BSEnd=0;
|
|
Chipset.P1Cfig=FALSE;Chipset.P1Cfg2=FALSE;Chipset.P1Base=0;Chipset.P1Size=0;Chipset.P1End=0;
|
|
Chipset.P2Cfig=FALSE;Chipset.P2Cfg2=FALSE;Chipset.P2Base=0;Chipset.P2Size=0;Chipset.P2End=0;
|
|
Map(0x00,0xFF); // refresh mapping
|
|
return;
|
|
}
|
|
|
|
VOID C_Eq_Id()
|
|
{
|
|
// config order is HDW, RAM, CE1, CE2, NCE3
|
|
if (!Chipset.IOCfig) {Nunpack(Chipset.C,(Chipset.IOBase) ^0x00019,5);return;}
|
|
if (!Chipset.P0Cfg2) {Nunpack(Chipset.C,(Chipset.P0Size*0x1000)^0xFF003,5);return;}
|
|
if (!Chipset.P0Cfig) {Nunpack(Chipset.C,(Chipset.P0Base*0x1000)^0x000F4,5);return;}
|
|
if (cCurrentRomType=='S') // HP48SX
|
|
{
|
|
if (!Chipset.P1Cfg2) {Nunpack(Chipset.C,(Chipset.P1Size*0x1000)^0xFF005,5);return;}
|
|
if (!Chipset.P1Cfig) {Nunpack(Chipset.C,(Chipset.P1Base*0x1000)^0x000F6,5);return;}
|
|
if (!Chipset.P2Cfg2) {Nunpack(Chipset.C,(Chipset.P2Size*0x1000)^0xFF007,5);return;}
|
|
if (!Chipset.P2Cfig) {Nunpack(Chipset.C,(Chipset.P2Base*0x1000)^0x000F8,5);return;}
|
|
if (!Chipset.BSCfg2) {Nunpack(Chipset.C,(Chipset.BSSize*0x1000)^0xFF001,5);return;}
|
|
if (!Chipset.BSCfig) {Nunpack(Chipset.C,(Chipset.BSBase*0x1000)^0x000F2,5);return;}
|
|
}
|
|
else // HP48GX / HP49G
|
|
{
|
|
if (!Chipset.BSCfg2) {Nunpack(Chipset.C,(Chipset.BSSize*0x1000)^0xFF005,5);return;}
|
|
if (!Chipset.BSCfig) {Nunpack(Chipset.C,(Chipset.BSBase*0x1000)^0x000F6,5);return;}
|
|
if (!Chipset.P1Cfg2) {Nunpack(Chipset.C,(Chipset.P1Size*0x1000)^0xFF007,5);return;}
|
|
if (!Chipset.P1Cfig) {Nunpack(Chipset.C,(Chipset.P1Base*0x1000)^0x000F8,5);return;}
|
|
if (!Chipset.P2Cfg2) {Nunpack(Chipset.C,(Chipset.P2Size*0x1000)^0xFF001,5);return;}
|
|
if (!Chipset.P2Cfig) {Nunpack(Chipset.C,(Chipset.P2Base*0x1000)^0x000F2,5);return;}
|
|
}
|
|
memset(Chipset.C,0,5);
|
|
return;
|
|
}
|
|
|
|
enum MMUMAP MapData(DWORD d) // check MMU area
|
|
{
|
|
BYTE u = (BYTE) (d>>12);
|
|
|
|
if (Chipset.IOCfig && ((d&0xFFFC0)==Chipset.IOBase)) return M_IO;
|
|
if (Chipset.P0Cfig && (((u^Chipset.P0Base) & ~Chipset.P0Size) == 0)) return M_RAM;
|
|
if (cCurrentRomType == 'S')
|
|
{
|
|
if (Chipset.P2Cfig && (((u^Chipset.P2Base) & ~Chipset.P2Size) == 0)) return M_P2;
|
|
if (Chipset.P1Cfig && (((u^Chipset.P1Base) & ~Chipset.P1Size) == 0)) return M_P1;
|
|
if (Chipset.BSCfig && (((u^Chipset.BSBase) & ~Chipset.BSSize) == 0)) return M_BS;
|
|
}
|
|
else
|
|
{
|
|
if (Chipset.P1Cfig && (((u^Chipset.P1Base) & ~Chipset.P1Size) == 0)) return M_P1;
|
|
if (Chipset.BSCfig && (((u^Chipset.BSBase) & ~Chipset.BSSize) == 0)) return M_BS;
|
|
if (Chipset.P2Cfig && (((u^Chipset.P2Base) & ~Chipset.P2Size) == 0)) return M_P2;
|
|
}
|
|
return M_ROM;
|
|
}
|
|
|
|
VOID CpuReset(VOID) // register setting after Cpu Reset
|
|
{
|
|
StopTimers(); // stop timer, do here because function change Chipset.t2
|
|
|
|
Chipset.pc = 0;
|
|
Chipset.rstkp = 0;
|
|
ZeroMemory(Chipset.rstk,sizeof(Chipset.rstk));
|
|
Chipset.HST = 0;
|
|
Chipset.SoftInt = FALSE;
|
|
Chipset.Shutdn = TRUE;
|
|
Chipset.inte = TRUE; // enable interrupts
|
|
Chipset.intk = TRUE; // INTON
|
|
Chipset.intd = FALSE; // no keyboard interrupts pending
|
|
Chipset.crc = 0;
|
|
Chipset.Bank_FF = 0; // state of bank switcher FF
|
|
Chipset.FlashRomState = 0; // WSM state of flash memory
|
|
ZeroMemory(Chipset.IORam,sizeof(Chipset.IORam));
|
|
Chipset.IORam[LPE] = RST; // set ReSeT bit at hardware reset
|
|
Reset(); // reset MMU
|
|
Chipset.t1 = 0; // reset timer values
|
|
Chipset.t2 = 0;
|
|
Chipset.loffset = 0; // right margin
|
|
Chipset.boffset = 0; // left margin
|
|
Chipset.lcounter = 0; // number of main display lines
|
|
Chipset.contrast = 0; // contrast dark
|
|
|
|
UpdateContrast(Chipset.contrast); // update contrast
|
|
// display update when changing to run state
|
|
CommSetBaud(); // new baudrate
|
|
CheckSerial(); // close serial port
|
|
|
|
RomSwitch(Chipset.Bank_FF); // force new memory mapping
|
|
return;
|
|
}
|
|
|
|
VOID Npeek(BYTE *a, DWORD d, UINT s)
|
|
{
|
|
enum MMUMAP eMap;
|
|
DWORD u, v;
|
|
UINT c;
|
|
BYTE *p;
|
|
|
|
do
|
|
{
|
|
eMap = MapData(d); // get active memory controller
|
|
if (M_IO == eMap) // I/O access
|
|
{
|
|
v = d&0x3F;
|
|
|
|
do
|
|
{
|
|
if (v == LPE)
|
|
{
|
|
// don't read LPE content with the function ReadIO()
|
|
c = 1;
|
|
memcpy(a, Chipset.IORam+v, c);
|
|
break;
|
|
}
|
|
if (v >= RBR_LSB && v <= RBR_MSB)
|
|
{
|
|
// don't read RBR content with the function ReadIO()
|
|
c = MIN(s,RBR_MSB-v+1);
|
|
memcpy(a, Chipset.IORam+v, c);
|
|
break;
|
|
}
|
|
// all others registers
|
|
do
|
|
{
|
|
if (v < LPE)
|
|
{
|
|
c = MIN(s,LPE-v);
|
|
break;
|
|
}
|
|
if (v < RBR_LSB && (v+s) > RBR_LSB)
|
|
{
|
|
c = MIN(s,RBR_LSB-v);
|
|
break;
|
|
}
|
|
c = MIN(s,0x40-v);
|
|
}
|
|
while (0);
|
|
ReadIO(a,v,c,FALSE);
|
|
}
|
|
while (0);
|
|
}
|
|
else
|
|
{
|
|
u = d>>12;
|
|
v = d&0xFFF;
|
|
c = MIN(s,0x1000-v);
|
|
// Flash memory Read access
|
|
if (cCurrentRomType=='X' && (Chipset.IORam[LCR] & LED) && M_P2 == eMap)
|
|
{
|
|
FlashRead(a, FlashROMAddr(d), c);
|
|
}
|
|
else
|
|
{
|
|
if ((p=RMap[u]) != NULL) // module mapped
|
|
{
|
|
memcpy(a, p+v, c);
|
|
}
|
|
else // open data bus
|
|
{
|
|
for (u=0; u<c; ++u) // fill all nibbles
|
|
{
|
|
if ((v+u) & 1) // odd address
|
|
a[u] = READODD;
|
|
else // even address
|
|
a[u] = READEVEN;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
a+=c;
|
|
d=(d+c)&0xFFFFF;
|
|
} while (s-=c);
|
|
return;
|
|
}
|
|
|
|
VOID Nread(BYTE *a, DWORD d, UINT s)
|
|
{
|
|
enum MMUMAP eMap;
|
|
DWORD u, v;
|
|
UINT c;
|
|
BYTE *p;
|
|
|
|
do
|
|
{
|
|
eMap = MapData(d); // get active memory controller
|
|
if (M_IO == eMap) // I/O access
|
|
{
|
|
v = d&0x3F;
|
|
c = MIN(s,0x40-v);
|
|
ReadIO(a,v,c,TRUE);
|
|
|
|
// reading MSB of timer2 update the CRC register
|
|
if (v+c == 0x40) UpCRC(a[c-1]); // timer2 MSB touched, update the CRC register
|
|
}
|
|
else
|
|
{
|
|
u = d>>12;
|
|
v = d&0xFFF;
|
|
c = MIN(s,0x1000-v);
|
|
// bank switcher access
|
|
if (cCurrentRomType!='S' && M_BS == eMap)
|
|
{
|
|
if (cCurrentRomType=='G') // HP48GX
|
|
{
|
|
Chipset.Bank_FF = v+c; // save FF value
|
|
Map(Chipset.P2Base,Chipset.P2End);
|
|
}
|
|
if (cCurrentRomType=='E' || cCurrentRomType=='X') // HP39/40G, HP49G
|
|
{
|
|
RomSwitch(v+c);
|
|
}
|
|
}
|
|
// Flash memory Read access
|
|
if (cCurrentRomType=='X' && (Chipset.IORam[LCR] & LED) && M_P2 == eMap)
|
|
{
|
|
DWORD dwLinAddr = FlashROMAddr(d);
|
|
|
|
FlashRead(a, dwLinAddr, c);
|
|
|
|
#if defined DEBUG_FLASH
|
|
{
|
|
TCHAR buffer[256];
|
|
DWORD j;
|
|
int i;
|
|
|
|
i = wsprintf(buffer,_T("%.5lx: Flash Read : %.5x (%.6x),%u = "),Chipset.pc,d,dwLinAddr,c);
|
|
for (j = 0;j < c;++j,++i)
|
|
{
|
|
buffer[i] = a[j];
|
|
if (buffer[i] > 9) buffer[i] += _T('a') - _T('9') - 1;
|
|
buffer[i] += _T('0');
|
|
}
|
|
buffer[i++] = _T('\n');
|
|
buffer[i] = 0;
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
else
|
|
{
|
|
if ((p=RMap[u]) != NULL) // module mapped
|
|
{
|
|
memcpy(a, p+v, c);
|
|
}
|
|
// simulate open data bus
|
|
else // open data bus
|
|
{
|
|
for (u=0; u<c; ++u) // fill all nibbles
|
|
{
|
|
if ((v+u) & 1) // odd address
|
|
a[u] = READODD;
|
|
else // even address
|
|
a[u] = READEVEN;
|
|
}
|
|
}
|
|
}
|
|
|
|
for (u=0; u<c; u++) // update CRC
|
|
UpCRC(a[u]);
|
|
}
|
|
a+=c;
|
|
d=(d+c)&0xFFFFF;
|
|
} while (s-=c);
|
|
return;
|
|
}
|
|
|
|
VOID Nwrite(BYTE *a, DWORD d, UINT s)
|
|
{
|
|
enum MMUMAP eMap;
|
|
DWORD u, v;
|
|
UINT c;
|
|
BYTE *p;
|
|
|
|
do
|
|
{
|
|
eMap = MapData(d); // get active memory controller
|
|
if (M_IO == eMap) // I/O access
|
|
{
|
|
v = d&0x3F;
|
|
c = MIN(s,0x40-v);
|
|
WriteIO(a, v, c);
|
|
}
|
|
else
|
|
{
|
|
u = d>>12;
|
|
v = d&0xFFF;
|
|
c = MIN(s,0x1000-v);
|
|
// bank switcher access
|
|
if (cCurrentRomType!='S' && M_BS == eMap)
|
|
{
|
|
BOOL bWrite = FALSE;
|
|
|
|
// write enabled
|
|
if (Chipset.cards_status & PORT2_WRITE)
|
|
{
|
|
Chipset.Bank_FF = v+c-1;// save FF value
|
|
bWrite = TRUE; // bank switched
|
|
}
|
|
else // write disabled, so latch last read cycle
|
|
{
|
|
if ((v & 1) != 0) // low address odd
|
|
{
|
|
Chipset.Bank_FF = v;// save FF value
|
|
bWrite = TRUE; // bank switched
|
|
}
|
|
|
|
if (((v+c) & 1) != 0) // high address odd
|
|
{
|
|
Chipset.Bank_FF = v+c-1;// save FF value
|
|
bWrite = TRUE; // bank switched
|
|
}
|
|
}
|
|
|
|
if (bWrite) // write cycle?
|
|
{
|
|
// HP48GX
|
|
if (cCurrentRomType=='G') Map(Chipset.P2Base,Chipset.P2End);
|
|
// HP39/40G, HP49G
|
|
if (cCurrentRomType=='E' || cCurrentRomType=='X') RomSwitch(Chipset.Bank_FF);
|
|
}
|
|
}
|
|
// Flash memory Write access
|
|
if (cCurrentRomType=='X' && (Chipset.IORam[LCR] & LED) && M_P2 == eMap)
|
|
{
|
|
DWORD dwLinAddr = FlashROMAddr(d);
|
|
|
|
FlashWrite(a, dwLinAddr, c);
|
|
|
|
#if defined DEBUG_FLASH
|
|
{
|
|
TCHAR buffer[256];
|
|
DWORD j;
|
|
int i;
|
|
|
|
i = wsprintf(buffer,_T("%.5lx: Flash Write: %.5x (%.6x),%u = "),Chipset.pc,d,dwLinAddr,c);
|
|
for (j = 0;j < c;++j,++i)
|
|
{
|
|
buffer[i] = a[j];
|
|
if (buffer[i] > 9) buffer[i] += _T('a') - _T('9') - 1;
|
|
buffer[i] += _T('0');
|
|
}
|
|
buffer[i++] = _T('\n');
|
|
buffer[i] = 0;
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
else
|
|
{
|
|
if ((p=WMap[u]) != NULL) memcpy(p+v, a, c);
|
|
}
|
|
}
|
|
if (!bGrayscale) UpdateDisplay(d, c); // update display
|
|
a+=c;
|
|
d=(d+c)&0xFFFFF;
|
|
} while (s-=c);
|
|
return;
|
|
}
|
|
|
|
DWORD Read5(DWORD d)
|
|
{
|
|
BYTE p[5];
|
|
|
|
Npeek(p,d,5);
|
|
return Npack(p,5);
|
|
}
|
|
|
|
BYTE Read2(DWORD d)
|
|
{
|
|
BYTE p[2];
|
|
|
|
Npeek(p,d,2);
|
|
return (BYTE)(p[0]|(p[1]<<4));
|
|
}
|
|
|
|
VOID Write5(DWORD d, DWORD n)
|
|
{
|
|
BYTE p[5];
|
|
|
|
Nunpack(p,n,5);
|
|
Nwrite(p,d,5);
|
|
return;
|
|
}
|
|
|
|
VOID Write2(DWORD d, BYTE n)
|
|
{
|
|
BYTE p[2];
|
|
|
|
Nunpack(p,n,2);
|
|
Nwrite(p,d,2);
|
|
return;
|
|
}
|
|
|
|
VOID IOBit(DWORD d, BYTE b, BOOL s) // set/clear bit in I/O section
|
|
{
|
|
EnterCriticalSection(&csIOLock);
|
|
{
|
|
if (s)
|
|
Chipset.IORam[d] |= b; // set bit
|
|
else
|
|
Chipset.IORam[d] &= ~b; // clear bit
|
|
}
|
|
LeaveCriticalSection(&csIOLock);
|
|
}
|
|
|
|
static DWORD ReadT2Acc(VOID)
|
|
{
|
|
static DWORD dwCyc = 0; // CPU cycle counter at last timer2 read access
|
|
|
|
DWORD dwCycDif;
|
|
|
|
// CPU cycles since last call
|
|
dwCycDif = (DWORD) (Chipset.cycles & 0xFFFFFFFF) - dwCyc;
|
|
dwCyc = (DWORD) (Chipset.cycles & 0xFFFFFFFF);
|
|
|
|
// maybe CPU speed measurement, slow down the next 10 CPU opcodes
|
|
if (dwCycDif < 150)
|
|
{
|
|
EnterCriticalSection(&csSlowLock);
|
|
{
|
|
InitAdjustSpeed(); // init variables if necessary
|
|
nOpcSlow = 10; // slow down next 10 opcodes
|
|
}
|
|
LeaveCriticalSection(&csSlowLock);
|
|
}
|
|
return ReadT2();
|
|
}
|
|
|
|
VOID ReadIO(BYTE *a, DWORD d, DWORD s, BOOL bUpdate)
|
|
{
|
|
BOOL bNINT,bNINT2;
|
|
BOOL bLBI,bVLBI;
|
|
|
|
BYTE c = 0xFF; // LINECOUNT not initialized
|
|
BOOL rbr_acc = FALSE; // flag to receive data
|
|
|
|
#if defined DEBUG_IO
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: IO read : %02x,%u\n"),Chipset.pc,d,s);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
|
|
do
|
|
{
|
|
switch (d)
|
|
{
|
|
case 0x00: *a = (Chipset.IORam[d]&DON)|Chipset.boffset; break;
|
|
case 0x01: *a = Chipset.contrast&0xF; break;
|
|
case 0x02: *a = Chipset.contrast>>4; break;
|
|
case 0x03: *a = 0;
|
|
case 0x04: *a = (Chipset.crc )&0xF; break;
|
|
case 0x05: *a = (Chipset.crc>> 4)&0xF; break;
|
|
case 0x06: *a = (Chipset.crc>> 8)&0xF; break;
|
|
case 0x07: *a = (Chipset.crc>>12)&0xF; break;
|
|
case 0x08: // LPD
|
|
// LB2 and LB1 not emulated, must be 0
|
|
_ASSERT((Chipset.IORam[LPD] & (LB2 | LB1)) == 0);
|
|
|
|
GetBatteryState(&bLBI,&bVLBI); // get battery state
|
|
|
|
// check if battery states enabled
|
|
bLBI = bLBI && ((Chipset.IORam[LPE] & ELBI) != 0);
|
|
bVLBI = bVLBI && ((Chipset.IORam[LPE] & EVLBI) != 0);
|
|
|
|
// set IO bits
|
|
IOBit(LPD,LB0,bLBI);
|
|
IOBit(LPD,VLBI,bVLBI);
|
|
IOBit(SRQ1,VSRQ,bVLBI);
|
|
*a = Chipset.IORam[d];
|
|
break;
|
|
case 0x09: // LPE
|
|
*a = Chipset.IORam[d];
|
|
if (bUpdate)
|
|
{
|
|
Chipset.IORam[d] &= ~RST; // clear RST bit after reading
|
|
}
|
|
break;
|
|
case 0x0A: *a = 0; break;
|
|
// case 0x0B: *a = Chipset.IORam[d]; break;
|
|
// case 0x0C: *a = Chipset.IORam[d]; break;
|
|
case 0x0D: // BAUD
|
|
*a = Chipset.IORam[d] & 0x7;
|
|
#if defined DEBUG_SERIAL // return BAUD value
|
|
if (bUpdate)
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: BAUD Read: %x\n"),Chipset.pc,*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
*a |= UckBit(*a); // add UCK bit to BAUD rate register
|
|
break;
|
|
case 0x0E:
|
|
// SMP is !NINT and SWINT is always 0
|
|
// clear SMP and SWINT bit
|
|
Chipset.IORam[d] &= (ECDT | RCDT);
|
|
// SMP is !NINT
|
|
if ((Chipset.IORam[SRQ2] & NINT) == 0)
|
|
Chipset.IORam[d] |= SMP;
|
|
*a = Chipset.IORam[d];
|
|
break;
|
|
case 0x0F:
|
|
// card detection disabled
|
|
if ((Chipset.IORam[CARDCTL] & ECDT) == 0)
|
|
{
|
|
*a = 0; // no cards
|
|
}
|
|
else
|
|
{
|
|
// on a HP30/40G and HP49G Chipset.cards_status bust always be 0xF
|
|
_ASSERT((cCurrentRomType!='E' && cCurrentRomType!='X') || Chipset.cards_status == 0xF);
|
|
*a = Chipset.cards_status;
|
|
}
|
|
break;
|
|
case 0x10: // IO CONTROL
|
|
*a = Chipset.IORam[d]; // return IO CONTROL value
|
|
#if defined DEBUG_SERIAL
|
|
if (bUpdate)
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: IOC Read: %x\n"),Chipset.pc,*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
case 0x11: // RCS
|
|
*a = Chipset.IORam[d] | RX; // return RCS value
|
|
#if defined DEBUG_SERIAL
|
|
if (bUpdate)
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: RCS Read: %x\n"),Chipset.pc,*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
case 0x12: // TCS
|
|
*a = Chipset.IORam[d]; // return TCS value
|
|
#if defined DEBUG_SERIAL
|
|
if (bUpdate)
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: TCS Read: %x\n"),Chipset.pc,*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
case 0x13: // CRER
|
|
*a = 0;
|
|
break;
|
|
case 0x14: // RBR LSB
|
|
case 0x15: // RBR MSB
|
|
if (bUpdate)
|
|
{
|
|
Chipset.IORam[RCS] &= ~RBF;
|
|
*a = Chipset.IORam[d]; // return RBR value
|
|
UpdateUSRQ(); // update USRQ
|
|
rbr_acc = TRUE; // search for new RBR value
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: RBR %s Read: %x\n"),Chipset.pc,(d==0x14) ? "LSB" : "MSB",*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
else
|
|
{
|
|
*a = Chipset.IORam[d]; // return RBR value
|
|
UpdateUSRQ(); // update USRQ
|
|
}
|
|
break;
|
|
// case 0x16: *a = Chipset.IORam[d]; break; // TBR LSB
|
|
// case 0x17: *a = Chipset.IORam[d]; break; // TBR MSB
|
|
case 0x19: // SREQ? MSB
|
|
UpdateKdnBit(); // update KDN bit
|
|
bNINT2 = Chipset.IORam[SRQ1] == 0 && (Chipset.IORam[SRQ2] & LSRQ) == 0;
|
|
bNINT = (Chipset.IORam[SRQ2] & NINT) != 0;
|
|
// card detection off and timer running
|
|
if ((Chipset.IORam[CARDCTL] & ECDT) == 0 && (Chipset.IORam[TIMER2_CTRL] & RUN) != 0)
|
|
{
|
|
// state of CDT2
|
|
bNINT2 = bNINT2 && (Chipset.cards_status & (P2W|P2C)) != P2C;
|
|
// state of CDT1
|
|
bNINT = bNINT && (Chipset.cards_status & (P1W|P1C)) != P1C;
|
|
}
|
|
IOBit(SRQ2,NINT2,bNINT2);
|
|
IOBit(SRQ2,NINT,bNINT);
|
|
// no break!
|
|
case 0x18: // SREQ? LSB
|
|
*a = Chipset.IORam[d]; // return SREQ value
|
|
#if defined DEBUG_SERIAL
|
|
if (bUpdate)
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: SEQ %s Read: %x\n"),Chipset.pc,(d==0x18) ? "LSB" : "MSB",*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
case 0x1A: // IR CONTROL
|
|
if (cCurrentRomType=='E') // HP39/40G
|
|
{
|
|
Chipset.IORam[d] = (nCurrentClass != 40)
|
|
? (Chipset.IORam[d] & ~IRI) // HP39G
|
|
: (Chipset.IORam[d] | IRI); // HP40G
|
|
}
|
|
*a = Chipset.IORam[d]; // return IR CONTROL value
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: IRC Read: %x\n"),Chipset.pc,*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
case 0x1B: *a = 0; break;
|
|
case 0x1C: // LED CONTROL
|
|
// put LBF and LBZ always to zero to indicate a free REDEYE buffer and formatter
|
|
*a = (Chipset.IORam[d] & (LED|ELBE));
|
|
break;
|
|
case 0x1D: // LED BUFFER
|
|
*a = (Chipset.IORam[d] & LBO);
|
|
break;
|
|
// case 0x1E: *a = Chipset.IORam[d]; break;
|
|
// case 0x1F: *a = Chipset.IORam[d]; break;
|
|
case 0x20: *a = 3; break;
|
|
case 0x21: *a = 3; break;
|
|
case 0x22: *a = 3; break;
|
|
case 0x23: *a = 3; break;
|
|
case 0x24: *a = 3; break;
|
|
case 0x25: *a = 3; break;
|
|
case 0x26: *a = 3; break;
|
|
case 0x27: *a = 3; break;
|
|
case 0x28: // LINECOUNT LSB
|
|
case 0x29: // LINECOUNT MSB + DA19 M32
|
|
if (Chipset.IORam[0x00]&DON) // display on
|
|
{
|
|
if (c == 0xFF) // no actual line information
|
|
{
|
|
c = GetLineCounter(); // get LCD update line
|
|
// save line information in IO registers
|
|
Chipset.IORam[0x28] = c & 0xF;
|
|
Chipset.IORam[0x29] = (Chipset.IORam[0x29] & (DA19|M32)) | (c >> 4);
|
|
}
|
|
}
|
|
*a = Chipset.IORam[d];
|
|
|
|
if (d==0x29) // address 0x29 is mirrored to 0x2A-0x2D
|
|
{
|
|
Chipset.IORam[0x2A] = *a;
|
|
Chipset.IORam[0x2B] = *a;
|
|
Chipset.IORam[0x2C] = *a;
|
|
Chipset.IORam[0x2D] = *a;
|
|
}
|
|
break;
|
|
// case 0x2A: *a = 0; break;
|
|
// case 0x2B: *a = 0; break;
|
|
// case 0x2C: *a = 0; break;
|
|
// case 0x2D: *a = 0; break;
|
|
case 0x2E:
|
|
ReadT1(); // dummy read for update timer1 control register
|
|
*a = Chipset.IORam[d];
|
|
break;
|
|
case 0x2F:
|
|
ReadT2(); // dummy read for update timer2 control register
|
|
*a = Chipset.IORam[d];
|
|
break;
|
|
case 0x30: *a = 3; break;
|
|
case 0x31: *a = 3; break;
|
|
case 0x32: *a = 3; break;
|
|
case 0x33: *a = 3; break;
|
|
case 0x34: *a = 3; break;
|
|
case 0x35: *a = 0; break;
|
|
case 0x36: *a = 0; break;
|
|
case 0x37: *a = ReadT1(); break;
|
|
case 0x38: Nunpack(a, ReadT2Acc() , s); return;
|
|
case 0x39: Nunpack(a, ReadT2Acc()>> 4, s); return;
|
|
case 0x3A: Nunpack(a, ReadT2Acc()>> 8, s); return;
|
|
case 0x3B: Nunpack(a, ReadT2Acc()>>12, s); return;
|
|
case 0x3C: Nunpack(a, ReadT2Acc()>>16, s); return;
|
|
case 0x3D: Nunpack(a, ReadT2Acc()>>20, s); return;
|
|
case 0x3E: Nunpack(a, ReadT2Acc()>>24, s); return;
|
|
case 0x3F: Nunpack(a, ReadT2Acc()>>28, s); return;
|
|
default: *a = Chipset.IORam[d];
|
|
}
|
|
d++; a++;
|
|
} while (--s);
|
|
if (rbr_acc) CommReceive(); // look for new character
|
|
return;
|
|
}
|
|
|
|
VOID WriteIO(BYTE *a, DWORD d, DWORD s)
|
|
{
|
|
DWORD b;
|
|
BYTE c;
|
|
BOOL tbr_acc = FALSE; // flag to transmit data
|
|
BOOL bDISPADDR = FALSE; // flag addr 0x120-0x124 changed
|
|
BOOL bLINEOFFS = FALSE; // flag addr 0x125-0x127 changed
|
|
BOOL bMENUADDR = FALSE; // flag addr 0x130-0x134 changed
|
|
DWORD dwAnnunciator = 0; // no annunciator write
|
|
|
|
#if defined DEBUG_IO
|
|
{
|
|
TCHAR buffer[256];
|
|
DWORD j;
|
|
int i;
|
|
|
|
i = wsprintf(buffer,_T("%.5lx: IO write: %02x,%u = "),Chipset.pc,d,s);
|
|
for (j = 0;j < s;++j,++i)
|
|
{
|
|
buffer[i] = a[j];
|
|
if (buffer[i] > 9) buffer[i] += _T('a') - _T('9') - 1;
|
|
buffer[i] += _T('0');
|
|
}
|
|
buffer[i++] = _T('\n');
|
|
buffer[i] = 0;
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
|
|
do
|
|
{
|
|
c = *a;
|
|
switch (d)
|
|
{
|
|
// 00100 = NS:DISPIO
|
|
// 00100 @ Display bit offset and DON [DON OFF2 OFF1 OFF0]
|
|
// 00100 @ 3 nibs for display offset (scrolling), DON=Display ON
|
|
case 0x00:
|
|
if ((c^Chipset.IORam[d])&DON) // DON bit changed
|
|
{
|
|
disp |= (DISP_POINTER | DISP_MAIN | DISP_MENUE);
|
|
|
|
// adjust VBL counter start/stop values
|
|
if ((c & DON) != 0) // set display on
|
|
{
|
|
Chipset.IORam[d] |= DON; // for StartDisplay();
|
|
UpdateContrast(Chipset.contrast);
|
|
StartDisplay((BYTE) Chipset.lcounter); // start display update
|
|
}
|
|
else // display is off
|
|
{
|
|
Chipset.IORam[d] &= ~DON;
|
|
UpdateContrast(Chipset.contrast);
|
|
StopDisplay(); // stop display update
|
|
}
|
|
}
|
|
// OFF bits changed
|
|
if ((c^Chipset.IORam[d]) & (OFF2 | OFF1 | OFF0))
|
|
{
|
|
Chipset.boffset = c & (OFF2 | OFF1 | OFF0);
|
|
disp |= (DISP_POINTER | DISP_MAIN);
|
|
}
|
|
Chipset.IORam[d] = c;
|
|
break;
|
|
|
|
// 00101 = NS:CONTRLSB
|
|
// 00101 @ Contrast Control [CON3 CON2 CON1 CON0]
|
|
// 00101 @ Higher value = darker screen
|
|
case 0x01:
|
|
if (c!=Chipset.IORam[d])
|
|
{
|
|
Chipset.IORam[d]=c;
|
|
Chipset.contrast = (Chipset.contrast&0x10)|c;
|
|
UpdateContrast(Chipset.contrast);
|
|
disp |= (DISP_MAIN | DISP_MENUE);
|
|
}
|
|
break;
|
|
|
|
// 00102 = NS:DISPTEST
|
|
// 00102 @ Display test [VDIG LID TRIM CON4] [LRT LRTD LRTC BIN]
|
|
// 00102 @ Normally zeros
|
|
case 0x02:
|
|
if (c!=Chipset.IORam[d])
|
|
{
|
|
Chipset.IORam[d]=c;
|
|
Chipset.contrast = (Chipset.contrast&0x0f)|((c&1)<<4);
|
|
UpdateContrast(Chipset.contrast);
|
|
disp |= (DISP_MAIN | DISP_MENUE);
|
|
}
|
|
break;
|
|
|
|
case 0x03: Chipset.IORam[d]=c; break;
|
|
|
|
// 00104 = HP:CRC
|
|
// 00104 @ 16 bit hardware CRC (104-107) (X^16+X^12+X^5+1)
|
|
// 00104 @ crc = ( crc >> 4 ) ^ ( ( ( crc ^ nib ) & 0x000F ) * 0x1081 );
|
|
case 0x04: Chipset.crc = (Chipset.crc&0xfff0)|(c*0x0001); break;
|
|
case 0x05: Chipset.crc = (Chipset.crc&0xff0f)|(c*0x0010); break;
|
|
case 0x06: Chipset.crc = (Chipset.crc&0xf0ff)|(c*0x0100); break;
|
|
case 0x07: Chipset.crc = (Chipset.crc&0x0fff)|(c*0x1000); break;
|
|
|
|
// 00108 = NS:POWERSTATUS
|
|
// 00108 @ Low power registers (108-109)
|
|
// 00108 @ [LB2 LB1 LB0 VLBI] (read only)
|
|
// 00108 @ LowBat(2) LowBat(1) LowBat(S) VeryLowBat
|
|
case 0x08: break; // read-only
|
|
|
|
// 00109 = NS:POWERCTRL
|
|
// 00109 @ [ELBI EVLBI GRST RST] (read/write)
|
|
case 0x09:
|
|
Chipset.IORam[d]=c;
|
|
if (c & RST)
|
|
{
|
|
CpuReset(); // emulate NRES signal
|
|
disp |= (DISP_POINTER | DISP_MAIN | DISP_MENUE);
|
|
dwAnnunciator = 0x3F; // update all annunciators
|
|
bInterrupt = TRUE; // SHUTDN
|
|
}
|
|
break;
|
|
|
|
// 0010A = NS:MODE
|
|
// 0010A @ Mode Register (read-only)
|
|
case 0x0A: break; // read-only
|
|
|
|
// 0010B = HP:ANNCTRL
|
|
// 0010B @ Annunciator control [LA4 LA3 LA2 LA1] = [ alarm alpha -> <- ]
|
|
case 0x0B:
|
|
case 0x0C:
|
|
// annunciator changed
|
|
dwAnnunciator |= ((Chipset.IORam[d] ^c) << ((d - 0x0B) * 4)) & 0x3F;
|
|
Chipset.IORam[d] = c;
|
|
break;
|
|
|
|
// 0010D = NS:BAUD
|
|
// 0010D @ Serial baud rate [UCK BD2 BD1 BD0] (bit 3 is read-only)
|
|
// 0010D @ 3 bits = {1200 1920 2400 3840 4800 7680 9600 15360}
|
|
case 0x0D:
|
|
Chipset.IORam[d]=(Chipset.IORam[d]&8)|(c&7); // bit 3 is read-only
|
|
CommSetBaud(); // set baudrate
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: BAUD write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
|
|
// 0010E = NS:CARDCTL
|
|
// 0010E @ [ECDT RCDT SMP SWINT] (read/write)
|
|
// 0010E @ Enable Card Det., Run Card Det., Set Module Pulled, Software interrupt
|
|
case 0x0E:
|
|
if (c & SWINT) // SWINT bit set
|
|
{
|
|
c &= (ECDT | RCDT | SMP); // clear SWINT bit
|
|
Chipset.SoftInt = TRUE;
|
|
bInterrupt = TRUE;
|
|
}
|
|
if ((c & SMP) == 0) // SMP bit cleared
|
|
{
|
|
BOOL bNINT = TRUE; // ack NINT interrupt -> NINT high
|
|
// card detect disabled and CDT1 low -> retrigger
|
|
if ((c & ECDT) == 0 && (Chipset.IORam[TIMER2_CTRL] & RUN) != 0)
|
|
bNINT = (Chipset.cards_status & (P1W|P1C)) != P1C;
|
|
IOBit(SRQ2,NINT,bNINT);
|
|
}
|
|
// falling edge of Enable Card Detect bit and timer running
|
|
if ( ((c^Chipset.IORam[d]) & ECDT) != 0 && (c & ECDT) == 0
|
|
&& (Chipset.IORam[TIMER2_CTRL] & RUN) != 0)
|
|
{
|
|
BOOL bNINT = (Chipset.IORam[SRQ2] & NINT) != 0;
|
|
// card in slot1 isn't Read Only
|
|
if ((Chipset.cards_status & (P1W|P1C)) != P1C)
|
|
{
|
|
// use random state of NINT line
|
|
bNINT = bNINT && (ReadT2() & 0x1) != 0;
|
|
}
|
|
IOBit(SRQ2,NINT,bNINT);
|
|
|
|
Chipset.HST |= MP; // set Module Pulled
|
|
|
|
// Port1 and Port2 plugged and writeable or NINT2/NINT interrupt
|
|
if ( Chipset.cards_status != (P2W|P1W|P2C|P1C)
|
|
|| (Chipset.IORam[SRQ2] & NINT2) == 0
|
|
|| (Chipset.IORam[SRQ2] & NINT ) == 0
|
|
)
|
|
{
|
|
Chipset.SoftInt = TRUE; // set interrupt
|
|
bInterrupt = TRUE;
|
|
}
|
|
}
|
|
Chipset.IORam[d]=c;
|
|
break;
|
|
|
|
// 0010F = NS:CARDSTATUS
|
|
// 0010F @ [P2W P1W P2C P1C] (read-only) Port 2 writable .. Port 1 inserted
|
|
case 0x0F: break; // read-only
|
|
|
|
// 00110 = HP:IOC
|
|
// 00110 @ Serial I/O Control [SON ETBE ERBF ERBZ]
|
|
// 00110 @ Serial On, Interrupt On Recv.Buf.Empty, Full, Buzy
|
|
case 0x10:
|
|
Chipset.IORam[d]=c;
|
|
CheckSerial(); // handle UART on/off
|
|
if ((c & SON) == 0) // SON bit cleared
|
|
{
|
|
Chipset.IORam[IOC] = 0; // clear IOC
|
|
Chipset.IORam[RCS] = 0; // clear RCS
|
|
Chipset.IORam[TCS] = 0; // clear TCS
|
|
Chipset.IORam[RBR_LSB] = 0; // clear RBR
|
|
Chipset.IORam[RBR_MSB] = 0;
|
|
Chipset.IORam[TBR_LSB] = 0; // clear TBR
|
|
Chipset.IORam[TBR_MSB] = 0;
|
|
}
|
|
if (UpdateUSRQ()) INTERRUPT; // update USRQ bit
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: IOC write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
|
|
// 00111 = HP:RCS
|
|
// 00111 Serial Receive Control/Status [RX RER RBZ RBF] (bit 3 is read-only)
|
|
case 0x11:
|
|
if (Chipset.IORam[IOC] & SON)
|
|
{
|
|
EnterCriticalSection(&csIOLock);
|
|
{
|
|
// critical section because of RER access
|
|
Chipset.IORam[d]=(Chipset.IORam[d]&8)|(c&7);
|
|
}
|
|
LeaveCriticalSection(&csIOLock);
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: RCS write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
break;
|
|
|
|
// 00112 = HP:TCS
|
|
// 00112 @ Serial Transmit Control/Status [BRK LPB TBZ TBF]
|
|
case 0x12:
|
|
if (Chipset.IORam[IOC] & SON)
|
|
{
|
|
Chipset.IORam[d]=c;
|
|
CommTxBRK(); // update BRK condition
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: TCS write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
break;
|
|
|
|
// 00113 = HP:CRER
|
|
// 00113 @ Serial Clear RER (writing anything clears RER bit)
|
|
case 0x13:
|
|
IOBit(RCS,RER,FALSE);
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: CRER write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
|
|
// 00114 = HP:RBR
|
|
// 00114 @ Serial Receive Buffer Register (Reading clears RBF bit)
|
|
case 0x14: break; // read-only
|
|
case 0x15: break; // read-only
|
|
|
|
// 00116 = HP:TBR
|
|
// 00116 @ Serial Transmit Buffer Register (Writing sets TBF bit)
|
|
case 0x16:
|
|
case 0x17:
|
|
if (Chipset.IORam[IOC] & SON)
|
|
{
|
|
Chipset.IORam[d]=c;
|
|
tbr_acc = TRUE; // new TBR value
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: TBR %s write: %x\n"),Chipset.pc,(d==0x16) ? "LSB" : "MSB",*a);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
break;
|
|
|
|
// 00118 = NS:SRR
|
|
// 00118 @ Service Request Register (read-only)
|
|
// 00118 @ [ISRQ TSRQ USRQ VSRQ] [KDN NINT2 NINT LSRQ]
|
|
case 0x18: break; // read-only
|
|
case 0x19: break; // read-only
|
|
|
|
// 0011A = HP:IRC
|
|
// 0011A @ IR Control Register [IRI EIRU EIRI IRE] (bit 3 is read-only)
|
|
// 0011A @ IR Input, Enable IR UART mode, Enable IR Interrupt, IR Event
|
|
case 0x1A:
|
|
// COM port open and EIRU bit changed
|
|
if (bCommInit && ((c^Chipset.IORam[d]) & EIRU) != 0)
|
|
{
|
|
// save new value for COM open
|
|
Chipset.IORam[d]=(Chipset.IORam[d]&8)|(c&7);
|
|
// reopen COM port with new setting
|
|
bCommInit = CommOpen(szSerialWire,szSerialIr);
|
|
}
|
|
Chipset.IORam[d]=(Chipset.IORam[d]&8)|(c&7);
|
|
#if defined DEBUG_SERIAL
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: IRC write: %x\n"),Chipset.pc,Chipset.IORam[d]);
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
break;
|
|
|
|
// 0011B = NS:BASENIBOFF
|
|
// 0011B @ Used as addressto get BASENIB from 11F to the 5th nibble
|
|
case 0x1B: break;
|
|
|
|
// 0011C = NS:LCR
|
|
// 0011C @ Led Control Register [LED ELBE LBZ LBF] (Setting LED is draining)
|
|
case 0x1C:
|
|
// HP49G new mapping on LED bit change
|
|
if (cCurrentRomType=='X' && ((c^Chipset.IORam[d])&LED))
|
|
{
|
|
Chipset.IORam[d]=c; // save new value for mapping
|
|
Map(Chipset.P2Base,Chipset.P2End); // new ROM mapping
|
|
#if defined DEBUG_FLASH
|
|
{
|
|
TCHAR buffer[256];
|
|
wsprintf(buffer,_T("%.5lx: NCE3: R%cM\n"),Chipset.pc,(c&LED) ? 'O' : 'A');
|
|
OutputDebugString(buffer);
|
|
}
|
|
#endif
|
|
}
|
|
if ((c^Chipset.IORam[d])&ELBE) // ELBE bit changed
|
|
{
|
|
// Led Service ReQuest on Led Buffer Empty enabled
|
|
BOOL bLSRQ = (c & (ELBE | LBF)) == ELBE;
|
|
|
|
IOBit(SRQ2,LSRQ,bLSRQ); // update LSRQ bit
|
|
if (bLSRQ) // interrupt on Led Buffer Empty enabled
|
|
{
|
|
Chipset.SoftInt = TRUE;
|
|
bInterrupt = TRUE;
|
|
}
|
|
}
|
|
Chipset.IORam[d]=c;
|
|
break;
|
|
|
|
// 0011D = NS:LBR
|
|
// 0011D @ Led Buffer Register [0 0 0 LBO] (bits 1-3 read zero)
|
|
case 0x1D:
|
|
IrPrinter((BYTE)(c&LBO));
|
|
Chipset.IORam[d]=c&LBO;
|
|
break;
|
|
|
|
// 0011E = NS:SCRATCHPAD
|
|
// 0011E @ Scratch pad
|
|
case 0x1E: Chipset.IORam[d]=c; break;
|
|
|
|
// 0011F = NS:BASENIB
|
|
// 0011F @ 7 or 8 for base memory
|
|
case 0x1F: Chipset.IORam[d]=c; break;
|
|
|
|
// 00120 = NS:DISPADDR
|
|
// 00120 @ Display Start Address (write only)
|
|
// 00120 @ bit 0 is ignored (display must start on byte boundary)
|
|
case 0x20:
|
|
case 0x21:
|
|
case 0x22:
|
|
case 0x23:
|
|
case 0x24:
|
|
Chipset.IORam[d]=c;
|
|
bDISPADDR = TRUE; // addr 0x120-0x124 changed
|
|
break;
|
|
|
|
// 00125 = NS:LINEOFFS
|
|
// 00125 @ Display Line offset (write only) (no of bytes skipped after each line)
|
|
// 00125 @ MSG sign extended
|
|
case 0x25:
|
|
case 0x26:
|
|
case 0x27:
|
|
Chipset.IORam[d]=c;
|
|
bLINEOFFS = TRUE; // addr 0x125-0x127 changed
|
|
break;
|
|
|
|
// 00128 = NS:LINECOUNT
|
|
// 00128 @ Display Line Counter and miscellaneous (28-29)
|
|
// 00128 @ [LC3 LC2 LC1 LC0] [DA19 M32 LC5 LC4]
|
|
// 00128 @ Line counter 6 bits -> max = 2^6-1 = 63 = disp height
|
|
// 00128 @ Normally has 55 -> Menu starts at display row 56
|
|
case 0x28:
|
|
// LSB of LINECOUNT changed
|
|
if (c != (BYTE) (Chipset.lcounter & 0xf))
|
|
{
|
|
Chipset.lcounter = (Chipset.lcounter & ~0xF) | c;
|
|
disp |= (DISP_POINTER | DISP_MAIN | DISP_MENUE);
|
|
}
|
|
break;
|
|
|
|
case 0x29:
|
|
// MSB of LINECOUNT changed
|
|
b = (c & 0x3) << 4; // upper two bits
|
|
if (b != (Chipset.lcounter & 0x30))
|
|
{
|
|
Chipset.lcounter = (Chipset.lcounter & ~0x30) | b;
|
|
disp |= (DISP_POINTER | DISP_MAIN | DISP_MENUE);
|
|
}
|
|
|
|
if ((c^Chipset.IORam[d])&DA19) // DA19 changed
|
|
{
|
|
Chipset.IORam[d]^=DA19; // save new DA19
|
|
Map(0x00,0xFF); // new ROM mapping
|
|
}
|
|
break;
|
|
|
|
case 0x2A: break;
|
|
case 0x2B: break;
|
|
case 0x2C: break;
|
|
case 0x2D: break;
|
|
|
|
// 0012E = NS:TIMER1CTRL
|
|
// 0012E @ TIMER1 Control [SRQ WKE INT XTRA]
|
|
case 0x2E:
|
|
Chipset.IORam[d]=c; // don't clear XTRA bit
|
|
ReadT1(); // dummy read for checking control bits
|
|
break;
|
|
|
|
// 0012F = NS:TIMER2CTRL
|
|
// 0012F @ TIMER2 Control [SRQ WKE INT RUN]
|
|
case 0x2F:
|
|
Chipset.IORam[d]=c;
|
|
ReadT2(); // dummy read for checking control bits
|
|
if (c&1)
|
|
StartTimers();
|
|
else
|
|
StopTimers();
|
|
dwAnnunciator = 0x3F; // update all annunciators
|
|
break;
|
|
|
|
// 00130 = NS:MENUADDR
|
|
// 00130 @ Display Secondary Start Address (write only) (30-34)
|
|
// 00130 @ Menu Display Address, no line offsets
|
|
case 0x30:
|
|
case 0x31:
|
|
case 0x32:
|
|
case 0x33:
|
|
case 0x34:
|
|
Chipset.IORam[d]=c;
|
|
bMENUADDR = TRUE; // addr 0x130-0x134 changed
|
|
break;
|
|
|
|
case 0x35: break;
|
|
case 0x36: break;
|
|
|
|
// 00137 = HP:TIMER1
|
|
// 00137 @ Decremented 16 times/s
|
|
case 0x37:
|
|
SetT1(c); // set new value
|
|
break;
|
|
|
|
// 00138 = HP:TIMER2
|
|
// 00138 @ hardware timer (38-3F), decremented 8192 times/s
|
|
// nothing - fall through to default
|
|
|
|
default:
|
|
Chipset.IORam[d]=c; // write data
|
|
|
|
if (d >= TIMER2) // timer2 update
|
|
{
|
|
Nunpack(Chipset.IORam+TIMER2,ReadT2(),8);
|
|
memcpy(Chipset.IORam+d,a,s);
|
|
SetT2(Npack(Chipset.IORam+TIMER2,8));
|
|
goto finish;
|
|
}
|
|
}
|
|
a++; d++;
|
|
} while (--s);
|
|
|
|
finish:
|
|
if (bDISPADDR) // 0x120-0x124 changed
|
|
{
|
|
b = Npack(Chipset.IORam+DISP1CTL,5)&0xFFFFE;
|
|
if (b != Chipset.start1)
|
|
{
|
|
Chipset.start1 = b;
|
|
disp |= (DISP_POINTER | DISP_MAIN);
|
|
}
|
|
}
|
|
if (bLINEOFFS) // addr 0x125-0x127 changed
|
|
{
|
|
signed short lo = (signed short)Npack(Chipset.IORam+LINENIBS,3);
|
|
if (lo&0x800) lo-=0x1000;
|
|
if (lo != Chipset.loffset)
|
|
{
|
|
Chipset.loffset = lo;
|
|
disp |= (DISP_POINTER | DISP_MAIN);
|
|
}
|
|
}
|
|
if (bMENUADDR) // addr 0x130-0x134 changed
|
|
{
|
|
b = Npack(Chipset.IORam+DISP2CTL,5)&0xFFFFE;
|
|
if (b != Chipset.start2)
|
|
{
|
|
Chipset.start2 = b;
|
|
disp |= (DISP_POINTER | DISP_MENUE);
|
|
}
|
|
}
|
|
|
|
if (tbr_acc) // addr 0x116-0x117 changed
|
|
{
|
|
IOBit(TCS,TBF,TRUE); // set transmit buffer full bit
|
|
CommTransmit(); // transmit char
|
|
}
|
|
|
|
if (disp & DISP_POINTER)
|
|
{
|
|
disp &= ~DISP_POINTER; // display pointer updated
|
|
UpdateDisplayPointers();
|
|
}
|
|
if (dwAnnunciator)
|
|
{
|
|
UpdateAnnunciators(dwAnnunciator);
|
|
}
|
|
return;
|
|
}
|