Previous behavior was that only if resolution and refresh rate match
exactly, the mode was accepted. As fallback, the mode with the highest
refresh rate and the same resolution was chosen.
New behavior is that the mode with the closest match for the refresh
rate is used with a limit of up to 1Hz. The fallback behavior stays the same.
Additionally, the logging was made more verbose.
This makes it possible to hint to the renderer and backends how many
bits per channel the buffers that the compositor draws windows onto
should have. Renderers and backends may deviate from this if they
do not support the formats with higher bit depth.
Wayland compositors handle many file descriptors: client
connections, DMA-BUFs, sync_files, wl_data_device pipes, and so
on. Bump the limit to the max.
Closes: https://github.com/swaywm/sway/issues/6285
Sometimes the preferred mode is not available due to hardware
constraints (e.g. GPU or cable bandwidth limitations). In these
cases it's better to fallback to lower modes than to end up with
a black screen.
Before this commit, when an output had its scale dynamically changed,
Sway would not load a cursor theme with the new scale. This results
in stale cursor images when moving the cursor into an area controlled
by the compositor, like the background or resize areas.
To reproduce:
- Using IPC, set an output scale to a value that isn't currently used
- Move the cursor into a compositor-controlled area
- The cursor will not change
Previously, we called output_disable prior to wlr_output_commit. This
mutates Sway's output state before the output commit actually succeeds.
This results in Sway's state getting out-of-sync with wlroots'.
An alternative fix [1] was to revert the changes made by output_disable
in case of failure. This is a little complicated. Instead, this patch
makes it so Sway's internal state is never changed before a successful
wlr_output commit.
We had two output flags: enabled and configured. However enabled was set
prior to the output becoming enabled, and was used to prevent the output
event handlers (specifically, the mode handler) from calling
apply_output_config again (infinite loop).
Rename enabled to enabling and use it exclusively for this purpose.
Rename configure to enabled, because that's what it really means.
[1]: https://github.com/swaywm/sway/pull/5521
Closes: https://github.com/swaywm/sway/issues/5483
We are not allowed to do what we did in #5222 and pass a `NULL` surface
wlr_seat_pointer_notify_enter(), and it's causing crashes when an
xdg-shell popup is active (see #5294 and swaywm/wlroots#2161).
Instead, solve #5220 using the new wlroots API introduced in
swaywm/wlroots#2217.
Previously in 3de1a39, it "worked by accident" in my testing since the
display being used in `map_to_output` was initialized first (the map
would not be applied because the display hadn't actually come online
yet), and was followed by a second display (at which point the map would
get applied for the first display).
Refs #5231
Some input rules, like `map_to_output`, are dependent on a specific
screen being present. This currently does not work for hotplugged
outputs, or outputs that are processed after the input device is
initially probed.
This commit fixes both cases, by reconfiguring inputs on each output
addition.
Fixes#5231.
An if branch takes care of the case where the output needs to be turned
off (DPMS'ed or disabled). The other branch needs to unconditionally
enable the output.
output->current_mode is already taken care of in apply_config.
Sorry about that, probably made a bad change by mistake after my DRM testing.
Closes: https://github.com/swaywm/sway/issues/5193
This enables/disables adaptive synchronization on the output.
For now, the default is disabled because it might cause flickering on
some hardware if clients don't submit frames at regular enough
intervals. In the future an "auto" option will only enable adaptive sync
if a fullscreen client opts-in via a Wayland protocol.
The output manager config is created when the output is created. It is
updated when the mode, transform, scale, or layout for the output
changes, as well as, when the output is destroyed.
Since the output->enabled property was not being set before calling
apply_output_config, the output event handlers were early returning and
never updating the output manager config when the output state was
committed.
This fixes the issue by setting output->enabled in apply_output_config
below the output disabling section. There are also a few other minor
changes that are required to function.
Additionally, this renames output_enable to output_configure to better
describe the recent changes.
The only output_enable caller is now apply_output_config. Stop calling
apply_output_config from output_enable to simplify the code and avoid
the back-and-forth between these two functions.
output_enable is now the symmetric of output_disable: it just marks the
output as enabled and performs bookkeeping (e.g. creating teh default
workspace). It is called from apply_output_config after the output
commit, so that it can read the current output state and act
accordingly.
This change also allows us to avoid an extraneous wlr_output_commit.
References: https://github.com/swaywm/sway/issues/4921
If applying an output config to an output fails, the output may be
destroyed. To be able to handle this situation correctly,
apply_output_config_to_outputs needs to use wl_list_for_each_safe.
set_cloexec is defined by both sway and wlroots (and who-knows-else),
so rename the sway one for supporting static linkage. We also remove
the duplicate version of this in client/.
Fixes: https://github.com/swaywm/sway/issues/4677
