/* (c) Raphaƫl Jacquot 2019 This file is part of hp_saturn. hp_saturn is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or any later version. hp_saturn is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with Foobar. If not, see . */ `default_nettype none `ifdef SIM module saturn_top; saturn_bus main_bus ( .i_clk (clk), .i_clk_en (clk_en), .i_reset (reset), .o_halt (halt), .o_char_to_send (char_to_send), .o_char_valid (char_valid), .i_serial_busy (serial_busy) ); saturn_serial serial_port ( .i_clk (clk), .i_char_to_send (char_to_send), .i_char_valid (char_valid), .o_serial_busy (serial_busy) ); wire [7:0] char_to_send; wire [0:0] char_valid; wire [0:0] serial_busy; wire [7:0] led; reg [0:0] reset; wire [0:0] halt; reg [0:0] clk; initial begin $display("TOP : starting the simulation"); clk = 0; reset = 1; @(posedge clk); @(posedge clk); @(posedge clk); reset = 0; $display("TOP : reset done, waiting for instructions"); @(posedge halt); $display("TOP : instructed to stop, halt is %b", halt); $finish; end always #10 clk = (clk === 1'b0); reg [3:0] delay; reg [0:0] clk_en; reg [7:0] test; initial begin delay = 4'b0001; clk_en = 1'b0; test = 8'b1; end always @(posedge clk) begin test <= {test[6:0], test[7]}; delay <= { delay[2:0], delay[3]}; clk_en <= delay[0]?1'b1:1'b0; if (reset) begin clk_en <= 1'b0; test <= 8'b1; end end endmodule `else /* * * * */ module saturn_top ( clk_25mhz, btn, led, wifi_gpio0, ftdi_rxd ); input wire [0:0] clk_25mhz; input wire [6:0] btn; output reg [7:0] led; output wire [0:0] wifi_gpio0; output wire [0:0] ftdi_rxd; /* this is necessary, otherwise, the esp32 module reboots the fpga in passthrough */ assign wifi_gpio0 = btn[0]; saturn_bus main_bus ( .i_clk (clk_25mhz), .i_clk_en (clk_en), .i_reset (reset), .o_halt (halt), .o_phase (phase), .o_cycle_ctr (cycle_ctr), .o_instr_decoded (instr_decoded), .o_debug_cycle (debug_cycle), .o_char_to_send (char_to_send), .o_char_counter (char_counter), .o_char_valid (char_valid), .o_char_send (char_send), .i_serial_busy (serial_busy) ); saturn_serial serial_port ( .i_clk (clk_25mhz), .i_char_to_send (char_to_send), .i_char_valid (char_valid), .o_serial_tx (ftdi_rxd), .o_serial_busy (serial_busy) ); reg [25:0] delay; reg [0:0] clk2; reg [0:0] clk_en; reg [0:0] reset; wire [0:0] halt; wire [1:0] phase; wire [31:0] cycle_ctr; wire [0:0] instr_decoded; wire [0:0] debug_cycle; wire [7:0] char_to_send; wire [9:0] char_counter; wire [0:0] char_valid; wire [0:0] char_send; wire [0:0] serial_busy; /* 1/4 s */ // `define DELAY_START 26'h20A1F0 // `define TEST_BIT 23 /* 1/8 s */ // `define DELAY_START 26'h1050F8 // `define TEST_BIT 22 /* 1/16 s */ `define DELAY_START 26'h08287C `define TEST_BIT 21 /* 1/32 s */ // `define DELAY_START 26'h4143E // `define TEST_BIT 20 initial begin led = 8'h00; delay = `DELAY_START; reset = 1'b1; clk2 = 1'b0; end always @(posedge clk_25mhz) begin reset <= btn[1]; delay <= delay[`TEST_BIT]?`DELAY_START:delay + 26'b1; clk_en <= (delay[`TEST_BIT]?1'b1:1'b0) && !halt; led[7] <= halt; led[6] <= char_send; led[5] <= serial_busy; led[4] <= debug_cycle; led[3] <= clk_en; led[2] <= instr_decoded; led[1:0] <= phase; end endmodule `endif